Gossen Metrawatt METRACLIP 63 Manual de Usario

Gossen Metrawatt Equipo de medición METRACLIP 63

Lee a continuación 📖 el manual en español para Gossen Metrawatt METRACLIP 63 (12 páginas) en la categoría Equipo de medición. Esta guía fue útil para 3 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/12

Operating Instructions

METRACLIP63 / 64

Milliampere Current Clamp

for Measuring Fault, Leakage and Stray Current 3-349-488-03

1/11.20

2 Gossen Metrawatt GmbH

1CT INPUT: Current clamp connector socket

2REC OUT: Connector sockets for data logger

3LCD panel

4AC / DC: Selector key for direct or

alternating current

5Range: Measuring range selector key

NOT AUTO

POWER OFF

: Key for deactivating auto-shutdown

7POWER: On/off key

80 SET: Zero balancing key

9DATA HOLD: Key for saving measured values

Scope of Delivery

1 measuring instrument

4 LR6 batteries (AA)

1 current clamp

1 carrying pouch

1 set of operating instructions

Measuring Instrument

Current Clamp

METRACLIP63

Current Clamp

METRACLIP64

1 Arrow must point

in direction of cur-

rent flow

2 Safety collar

3 Locking lever

4 Slider for opening

the clamp

Description in

section 4.1

1 Arrow must point

in direction of

current flow

2 Safety collar

3 Key for opening

the clamp

Gossen Metrawatt GmbH 3

Table of contents

1 Safety Precautions .............................3

1.1 General .......................................................3

1.1.1 Meaning of Symbols on the Instrument ..........4

2 Applications ........................................4

3 Initial Start-Up ....................................4

4 Operation ............................................5

4.1 Using the METRACLIP 63 Current Clamp .....5

4.2 Direct Current Measurement .........................5

4.3 Alternating Current Measurement .................6

4.4 Measuring Leakage and Stray Current ...........6

4.5 Using a Data Logger .....................................7

5 Characteristic Values ..........................8

6 Maintenance .....................................10

6.1 Housing .....................................................10

7 Repair and Replacement Parts Service,

DKD Calibration Laboratory and Rental

Instrument Service

.................................10

8 Product Support ................................11

1 Safety Precautions

1.1 General

You have selected an instrument which

provides you with high levels of safety.

This instrument fulfills all requirements of

applicable European and national EC

guidelines. We confirm this with the CE mark.

The relevant declaration of conformity can be

obtained from Gossen Metrawatt GmbH.

The METRACLIP 63 / 64 current clamp is

manufactured and tested in accordance with

safety regulations

IEC 61010-1/EN 61010-1/VDE 0411-1 and

IEC 61010-2-032/EN 61010-2-032/

VDE 0411-2-032. When used for its intended

purpose, safety of the operator, as well as that

of the instrument, is assured. Their safety is

however not guaranteed, if the instrument is

used improperly or handled carelessly.

In order to maintain flawless technical safety

conditions, and to assure safe use, it is impera-

tive that you read the operating instructions

thoroughly and carefully before placing your

instrument into service, and that you follow all

instructions contained therein.

Observe the following safety precautions:

• Avoid excessive mechanical stress such as

impact and vibration, as well as high tem-

peratures and humidity, because this may

result in damage to the instrument.

• Do not use this instrument in close

proximity to acids, alkaline salts, organic

solutions, corrosive gases etc.

• Do not use this instrument in proximity to

devices which generate strong magnetic

and/or electrical fields, because this may

result in malfunctioning.

• Do not use this instrument in operating

environments where dust or splash water

occur.

Attention!

Do not perform measurements at

cables with voltages of greater

than 600 V AC.

Before using the instrument, test the

voltage of the electrical circuit to be

measured.

Do not perform measurements on bare

wires!

Do not subject the input and output

sockets to voltages of greater than

10 V AC.

The current clamp may not be used:

• If the device, the housing or the cable is

damaged

• If the battery compartment lid has been

removed

• For current values which are

impermissible high for the current clamp

• In the rain, with wet hands, in the

presence of splashing water or in moist

environments

Especificaciones del producto

Marca:	Gossen Metrawatt
Categoría:	Equipo de medición
Modelo:	METRACLIP 63

¿Necesitas ayuda?

Si necesitas ayuda con Gossen Metrawatt METRACLIP 63 haz una pregunta a continuación y otros usuarios te responderán

Tu nombre*

Tu correo electrónico*

Escribe tu pregunta aquí

Equipo de medición Gossen Metrawatt Manuales

Gossen Metrawatt SECULIFE ST M693A Manual de Usario

19 Septiembre 2024

Gossen Metrawatt METRALINE VT SENSE M611K Manual de Usario

18 Septiembre 2024

Gossen Metrawatt METRALINE EARTH M590R Manual de Usario

17 Septiembre 2024

Gossen Metrawatt METRA Hit 27Ex Manual de Usario

16 Septiembre 2024

Gossen Metrawatt METRAOHM 10 Manual de Usario

15 Septiembre 2024

Gossen Metrawatt POINTAX 6000M Manual de Usario

14 Septiembre 2024

Gossen Metrawatt METRAHIT CAL Manual de Usario

14 Septiembre 2024

Gossen Metrawatt PROFITEST PV Manual de Usario

13 Septiembre 2024

Gossen Metrawatt METRAPhase 1 Manual de Usario

13 Septiembre 2024

Gossen Metrawatt SECUTEST 21F Manual de Usario

13 Septiembre 2024

Equipo de medición Manuales

Últimos Equipo de medición Manuales

PeakTech 1207 Manual de Usario

26 Octubre 2024

Kern FL 1KG Manual de Usario

25 Octubre 2024

PeakTech 6193 Manual de Usario

25 Octubre 2024

PCE Instruments PCE-TUM 50 Manual de Usario

24 Octubre 2024

PCE Instruments PCE-325D Manual de Usario

23 Octubre 2024

PCE Instruments PCE-AM 30 Manual de Usario

23 Octubre 2024

PCE Instruments PCE-900 Manual de Usario

23 Octubre 2024

PCE Instruments PCE-CSM 10 Manual de Usario

23 Octubre 2024

PCE Instruments PCE-CSM 7 Manual de Usario

23 Octubre 2024

PCE Instruments PCE-CSM 3 Manual de Usario

23 Octubre 2024